Showing results: 286 - 300 of 333 items found.
-
50-296A-021-1/24 -
Pickering Interfaces Ltd.
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
50-296A-021-2/16 -
Pickering Interfaces Ltd.
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
50-296A-021-2/12 -
Pickering Interfaces Ltd.
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
72-8495 -
Tenma
Compact 2-in-1 unit provides standard digital multimeter functions, as well as pin configurations on network and voice cables. Dual pinout indicator provides sequential verification of each pin on a network cable, and the included remote terminator allows testing of cables which are already installed. Digital multimeter measures AC/DC volts and amps, resistance and diodes, and provides audible continuity test.
-
PTE-100 -
SEICA SpA
The PTE-100 gives test personnel access to electrical signals for probing, voltage injection, isolation checks, voltage/current and time/frequency measurements, and it offers the ability to analyze hot and loaded circuits, verifying missing, corrupted or present valid signals. Furthermore, the PTE-100 offers the ability to make electrical verification activities more efficient, repeatable and safe, by introducing software controlled test sequences to reduce human errors and guide diagnostic resolution. Break Out Boxes are commonly made in-house and are often specific to a particular project. They are simply designed to multiplex connections between two units and use external instrumentation for signal injection or measurement. The end result is a multitude of tools, difficult to maintain, with limited transportability, providing costly and inefficient operations at the factory or in the field.
-
Amida Technology, Inc.
AMIDA 5000 is a high-end performance test system, combining analog, mixed-signal and logic with the latest test solutions. High pin count - as many as 512 smart multi-function pinframes and 128 sites. Ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. This system has a higher number of parallel tests and a higher level of capability. This series of test systems provides a powerful test combination with high-speed hardware and software integration. The 5000 series test system is the best analog, mixed signal, digital IC, PA test system for engineering verification and mass production. It can be easily connected to all well-known wafer probing machines and sorters, and also supports parallel test functions. The 5000 series meets customers' needs for high-precision, high-resolution, high-reliability, user-friendly, and low-cost testing and measurement of test systems.
-
USB Explorer 260 -
Ellisys Sàrl
The Ellisys USB Explorer 260 is a sophisticated protocol test system for USB traffic monitoring, driver and software stack debugging, protocol compliance verification and performance analysis. Analyze USB 1.1 and USB 2.0 links at any speed, including OTG and the new InterChip-USB at all speeds and all voltages; emulate USB hosts and devices; inject pre-defined error patterns for stress and error recovery testing.
-
TT9103 -
Matco Tools
*Portable and water resistant trailer light tester and trailer brakes tester that allows the user to perform all testing functions without the use of the vehicle*Tests 7-spade, 6-round and 4/5-flat pin type trailer harnesses*Short circuit protection*Turn signal simulation and power verification LED*Water resistant*Trickle charger and trailer plug adapter includedInternal battery compartment (battery not included)
-
Chroma Systems Solutions, Inc.
The Chroma programmable AC power source 61500/61600 series are the right solutions to meet complex single and three phase requirements due to their ability to simulate AC line conditions and measure critical product characteristics during testing. These features make the 61500/61600 series ideal for commercial, power electronics, avionics, military, and regulation test applications from bench-top R/D design verification and quality assurance to mass production.
-
ASTEL 3.2 TYPE -
MeterTest Ltd.
ASTeL 3.2 meter test equipment is a fully automatic system that enables simultaneous, multi-position calibration and verification of three-phase electric energy meters. ASTeL 3.2 offers full compatibility with IEC 60736. Thanks to excellent parameters, superior functionality and outstanding flexibility, ASTeL 3.2 is an ideal solution for utility companies, energy meter manufacturers, governmental institutes of metrology, metrological laboratories, and other customers interested in electricity meters testing.
-
ASTEL 1.2 TYPE -
MeterTest Ltd.
ASTeL 1.2 meter test equipment is a fully automatic system that enables simultaneous, multi-position calibration and verification of single-phase electric energy meters. ASTeL 1.2 offers full compatibility with IEC 60736. Thanks to excellent parameters, superior functionality and outstanding flexibility, ASTeL 1.2 is an ideal solution for utility companies, energy meter manufacturers, governmental institutes of metrology, metrological laboratories, and other customers interested in electricity meters testing.
-
ViTec Co. Ltd
The system of automatic calibration and verification consists of a computer of the operator's workplace and a control controller with a calibrator connected to it and a verified device. The device under test can have 4 to 16 working channels with a complicated circuit for connecting different types of signals: voltage, current, thermocouples, thermoresistance. The system allows a change in the set of operating ranges during calibration and calibration. The software development system used the LabVIEW development environment with the Real-Time module.
-
Model：OLT-20 -
ShinewayTech
OLT-20 Optical Loss Tester integrates laser source module and power meter module in one set, which can perform power testing and link loss testing in optic fiber network conveniently. The typical applications include fiber identification, attenuation and loss measurement, continuity verification and fiber link transmission quality evaluation for installation, routine inspection and daily maintenance of MAN, WAN and CATV systems as well as for lab test and research work.
-
GAO Tek Inc.
GAOTek provides a large collection of high quality, affordable E1 testers that are specially manufactured to speed up the ethernet maintenance time and work efficiency for sale to the United States, Canada and Globally. These devices consist of PING, router trace, a port location tool, a loop-back tool and offers a variety of Ethernet diagnostic functions. These E1 Ethernet test instruments are all incorporated with test tools for E1, V port, and Gigabit Ethernet link repairs, and failure diagnosis. E1 Ethernet testing devices are user-friendly, can be used in Ethernet cable tests, flux error code tests, connectivity performance, traffic testing, ethernet wire testing, and bandwidth verification. As these devices help in measuring and proving performance for criteria Ethernet networks they are commonly used in the RFC2544 performance test.
-
JTAG Interrogator -
Corelis, Inc.
Top manufacturers have used JTAG tests for years to ensure electronic systems are free from defects and assembled correctly. With growing uncertainty in supply chains and the proliferation of counterfeit components, that same technology can be used to verify the authenticity of system components.The Corelis JTAG Interrogator is an affordable solution for semiconductor verification. The software and hardware system provides the means to quickly identify components on an assembled electronic product by reading available information from the JTAG chain. Components can also be scanned to discover undocumented opcodes that may indicate hidden JTAG capabilities such as backdoors and harmful or malicious functions.Fast and nonintrusive JTAG component identification has never been so easy.
